Weak shower pressure, slow-filling fixtures, or poor flow throughout the house — we diagnose the actual cause and fix it permanently.
Low water pressure at a single faucet is almost always a clogged aerator — the small mesh screen at the faucet tip that collects mineral deposits over time. Unscrew it, rinse it, reinstall it. That's a 2-minute DIY fix that resolves approximately 60% of single-fixture pressure complaints. If that's your situation, we'll tell you that over the phone and save you the service call.
Whole-house low pressure is a different conversation. In High Point's pre-1970 homes, galvanized steel supply pipes are the most common culprit — internal corrosion reduces the pipe's effective interior diameter from 3/4 inch to as little as 1/4 inch over 50 years. The pressure isn't low because the water supply is weak; it's low because it's trying to push through a severely narrowed pipe. Only repiping solves this — but we confirm it before recommending it.
📞 Call Now — 336-422-7560We ask which fixtures are affected. Single fixture = local issue. Whole house or multiple fixtures = supply system, PRV, or pipe problem.
We measure actual pressure at a hose bib or laundry connection. Normal range is 45–80 PSI. This tells us immediately whether the issue is supply, PRV, or pipe restriction.
Low PRV output: replace the valve. Adequate pressure at meter but low at fixtures: galvanized pipe restriction. Low at meter: utility issue or service line problem.
We make the repair and re-measure pressure at multiple points to confirm improvement across the system.
Written quotes before any work begins. No hidden fees.
| Service | Typical Range |
|---|---|
| Pressure Diagnosis Service Call | $75 – $150 |
| PRV Replacement | $275 – $500 |
| Aerator Cleaning / Cartridge Replacement | $75 – $175 |
| Galvanized Pipe Section Replacement | $300 – $700 |
| Whole-House Repipe (pressure restoration) | $4,000 – $9,000 |
| Booster Pump Installation (high-elevation homes) | $600 – $1,200 |
Prices vary based on access, scope, and materials. Call for an exact quote.
We measure actual pressure numbers, not guesses. This drives the diagnosis and prevents unnecessary repair recommendations.
We've diagnosed and repiped dozens of older High Point homes with galvanized restriction. We know exactly what to look for.
If the fix is an aerator cleaning or a supply stop adjustment, we tell you — even if it means a $75 service call instead of a repiping recommendation.
Shower pressure had been terrible for years. Triad measured the pressure, confirmed galvanized pipes were the cause, and gave me a clear repipe quote. Repiped the whole house — pressure is incredible now.
Called about low pressure — they asked if it was one faucet or the whole house, then walked me through cleaning the aerator over the phone. Fixed it in 2 minutes. That kind of honest help builds real trust.
Had a failing PRV — pressure was swinging between 30 and 100 PSI randomly. Triad replaced it same day and the system has been rock steady since. Didn't realize how bad it was until it was fixed.
Sudden pressure loss at all fixtures simultaneously often indicates a utility issue (check with High Point Water Resources at 336-883-3111 first), a failing PRV, or a water meter issue. Gradual pressure loss over months or years is more commonly galvanized pipe restriction in older homes. The distinction between sudden and gradual helps narrow the cause significantly.
A pressure-reducing valve controls the municipal supply pressure down to a safe household level (typically 50–65 PSI). PRVs last 10–15 years, then fail in one of two ways: stuck closed (causing low pressure throughout the house) or stuck open (causing dangerously high pressure). If your home is over 10 years old and you have whole-house low pressure with no other obvious cause, the PRV is a strong candidate.
Yes — this is the most common cause of whole-house low pressure in High Point homes built before 1970. Galvanized steel corrodes from the inside, narrowing the effective pipe diameter over decades. A pipe that originally had 3/4-inch interior flow may have an effective diameter of 1/4 inch or less after 50 years of corrosion. Repiping with PEX restores full flow immediately.
Single-fixture pressure issues are almost always local: a clogged aerator (the mesh screen at the faucet tip), a partially closed supply stop valve under the sink, or a worn cartridge that's not opening fully. Start by cleaning the aerator — it's free and resolves most single-fixture complaints.
Normal residential water pressure ranges from 45–80 PSI. Below 45 PSI causes the weak pressure issues you'll notice. Above 80 PSI stresses pipe joints, faucet cartridges, and appliance connections, leading to premature failure and higher leak risk. High Point Water Resources supplies at higher pressures in some areas — a PRV set to 60–65 PSI protects your system.
Water pressure diagnosis and repair across High Point, NC. We find the real cause first.
Pressure diagnosis and repair across High Point and the Piedmont Triad.